User Tools
start
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
start [2019/04/25 14:10] thierry |
start [2019/04/25 14:38] (current) thierry [Troubleshooting] |
||
|---|---|---|---|
| Line 45: | Line 45: | ||
| |No production of purified water|- Power light ON \\ - indicator PUMP is off \\ - indicator SOURCE is ON| The inlet tap water supply is closed or has insufficient pressure|Improve water supply| | |No production of purified water|- Power light ON \\ - indicator PUMP is off \\ - indicator SOURCE is ON| The inlet tap water supply is closed or has insufficient pressure|Improve water supply| | ||
| | ::: | ::: | Water inlet tubing folded or obstructed|Check that the inlet pipe is not damaged.| | | ::: | ::: | Water inlet tubing folded or obstructed|Check that the inlet pipe is not damaged.| | ||
| - | | ::: |- Power light ON \\ - all control light indicators OFF|A fuse is broken :\\ - pump fuse \\ - fuse in the controller box| Check and replace the fuse| | + | | ::: |- Power light ON \\ - all control light indicators OFF|Fuse in the controller box broken | Replace fuse | |
| - | |Weak purified water production|- Power light ON \\ - indicator PUMP light ON \\ - Pump running|Pre-treatment clogged| Replace the pre-treatment filters before the RO membrane| | + | |reduced flow of purified water|- Power light ON \\ - indicator PUMP light ON \\ - Pump running continuously|Pre-treatment clogged| Replace the pre-treatment filters before the RO membrane| |
| | ::: | ::: | Weak flow of inlet water|Increase the flow of the inlet water| | | ::: | ::: | Weak flow of inlet water|Increase the flow of the inlet water| | ||
| | ::: | ::: | Reverse osmosis membrane clogged|Change the membrane | | | ::: | ::: | Reverse osmosis membrane clogged|Change the membrane | | ||
| + | | ::: |Pump leakage | Pump damaged|Replace the pump | | ||
| + | | ::: | ::: | Flow restrictor blocked| Replace flow restrictor | | ||
| | ::: | - Power light ON \\ - indicator PUMP light ON \\ - Pump always OFF|Pump fuse burned |Replace the pump fuse | | | ::: | - Power light ON \\ - indicator PUMP light ON \\ - Pump always OFF|Pump fuse burned |Replace the pump fuse | | ||
| - | | ::: | - Power light ON \\ - indicator PUMP light OFF \\ - Water output hand valve opened|High pressure switch blocked |- Adjust the screw of the high pressure switch \\ - Replace the high pressure switch | | ||
| | Starts and stops continuously | Light indicators FULL and PUMP alternate| Defective high-pressure sensor or check valve|Change pressure sensor and check valve| | | Starts and stops continuously | Light indicators FULL and PUMP alternate| Defective high-pressure sensor or check valve|Change pressure sensor and check valve| | ||
| - | |Lack of pressure on water output| - Power light ON | Watertank hand valve closed|Turn ON the watertank hand valve| | + | |Lack of pressure on purified water output| - Power light ON | Watertank hand valve closed|Turn ON the watertank hand valve| |
| | ::: | ::: | Requested pure water volume above the capacity of the water purifier|Wait the watertank is filled again\\ | | | ::: | ::: | Requested pure water volume above the capacity of the water purifier|Wait the watertank is filled again\\ | | ||
| | ::: | ::: | Lack of pressure in the pressurised watertank|Re-adjust the air-pressure of the water tank| | | ::: | ::: | Lack of pressure in the pressurised watertank|Re-adjust the air-pressure of the water tank| | ||
start.1556201458.txt.gz · Last modified: 2019/04/25 14:10 by thierry
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
